Introduction
Instructions Software
Vintages Download the Instruction Manual Here
Instructions
Table
of Commands available for LOG08-II
Commands
and parameters are not case-sensitive
|
Command
|
Description
|
Syntax
|
|
DEL
|
Delete
a sensor that was previously installed via the INI command
|
DEL<sensorid>
See Note 1
|
|
DIS
|
Display
serial numbers of all configured 1-Wire devices
|
DIS
|
|
DLO
|
Display
the log records. Output will
be time-stamped and the entries separated by commas.
|
DLO
|
|
DLR
|
Displays
log records that are new since the last DLR or DLO command.
The output is identical to the DLO command but records already
displayed are suppressed.
|
DLR
|
|
DUN
|
"Display
Units" - a flag to select whether or not the log file and output
displays includes the sensor unit (F,C,V, etc.)
|
DUN
<on|off>
|
|
EEP
|
Display
and change specific EEPROM memory locations
|
EEP
<start location><cr>
|
|
ERA
|
Erase
only the beginning of the EEPROM (includes sensors and log
pointers). Used when an ERF is not desirable.
|
ERA
|
|
ERF
|
Erase the
EEPROM (Note: due to the size of memory used, this will take considerable
time – use with discretion)
|
ERF
|
|
HLP
|
Display a
list of available commands
|
HLP
|
|
INI
|
Search
for a list of available 1-Wire sensors.
|
INI
|
|
LOG
|
Start or
stop the logging process
|
LOG
<on|off>
|
|
MEM
|
Display
and change specific memory locations
|
MEM
<start location><cr>
|
|
RST
|
Reset
any DS2423 counter
|
RST<sensorid>
|
|
SCK
|
Set
Clock
|
SCK
See
Note 4
|
|
SER
|
Display
the serial number of the LOG08-II
|
SER
|
|
SET
|
Configure
all system parameters
|
SET
|
|
SID
|
Show
the Serial Number ID for the 1-Wire Devices
|
SID
<on|off>
|
|
SPT
|
Set
the polling interval
|
SPT
xx
Where
xx is a decimal number from 00 to 99.
00 will disable polling and logging.
R will produce continuous polling and logging. M will set the timer to 180
minutes (3 hours)
|
|
SPR
|
Set
power restore logging. If set
to on, logging will resume after a power failure, if set to off, logging
will not resume after a power failure.
|
SPR
<on|off>
|
|
STD
|
Set
Temperature Display
|
STD
<F|C>
|
|
TIM
|
Display
Time from Real Time Clock
|
TIM
|
|
TMP
|
Display
sensor readings of all connected 1-Wire Devices in either verbose
(includes serial numbers) or non-verbose manner
|
TMP
|
|
TYP
|
Select
the type of DS2438 or DS2423 device.
See Table 3 in the
manual for valid types.
|
TYP<sensorid>
|
|
VER
|
Displays
the current version of the software loaded
|
VER
|
|
ZZZ
|
Performs
a reset of LOG08-II
|
ZZZ
|
Notes
- The
<sensorid> parameter in some commands above refers to the sensor
number as shown via the DIS command.
- Most
commands do not require a Carriage Return (enter) following the parameter or
command input. One exception is
the SCK command. Commands
requiring a sensor number input will require a CR if the sensor number is
only a single digit.
- Command
parameters are shown in angled brackets “< >”.
Where only certain options are permitted, they are indicated with a
vertical pipe character “|”.
- The
SCK command will prompt the user for the time and date input.
Please see the User
Manual for more information about LOG08-II commands and options.
|
